AlienFrac FIG 1502 hammer unions are designed for high-pressure oilfield connections. The catalogue specifies a replaceable resilient nitrile-butadiene rubber seal ring and a robust wall-thickness design. FIG 1502 is rated at 15,000 PSI NSCWP with a 22,500 PSI test pressure. Available catalogue sizes are 1½ in, 2 in and 3 in, with a blue nut and red parts for visual identification. The listed applications are cementing, fracturing, acidizing, testing, and choke & kill lines.
Pressure and color are quick identification cues, but they are not a substitute for checking the figure number, nominal size, markings, end requirement, and service conditions. For broader selection context, review the hammer union pressure ratings and color codes guide before confirming an order.
The table below reproduces the FIG 1502 catalogue values as supplied. Imperial and metric values are shown together and have not been recalculated or normalized.
| Nominal pipe size (in) | Nominal pipe size (mm) | Total length (in) | Total length (mm) | Pick bore (in) | Pick bore (mm) | Nut radius (in) | Nut radius (mm) | Nut material | Part material | Weight (lb) | Weight (kg) |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 1 1/2 | 38.1 | 5 13/32 | 137 | 1/4 | 6.4 | 3 21/32 | 93 | SF | SF | 12 | 5.4 |
| 2 | 50.8 | 7 | 177.8 | 16/84 | 6 | 3 3/4 | 95.3 | SF | SF | 21 | 9.5 |
| 3 | 76.2 | 7 6/8 | 193.7 | 3/8 | 9.5 | 4 1/2 | 114.3 | SF | SF | 31 | 14.1 |
The FIG 1502 union features a replaceable nitrile-butadiene rubber (NBR) seal ring and a robust wall design for high-pressure service. Seal condition, correct assembly, and application requirements should be verified before use. Sour-service suitability, material grade, certification, and interchangeability with other manufacturers’ unions should be confirmed separately rather than inferred from the FIG 1502 designation alone.
FIG 1502 may also be used in a pressureless seal connection, with butt-weld Sch. XXH specified as the preferred arrangement. Confirm the end configuration, mating components, and installation requirements for the actual system before purchase.
For an overview of threaded, butt-weld, socket-weld, and specialty arrangements across the wider product category, see the hammer union connection types guide.
To prepare a quotation, provide:
If you are checking an existing component, record the figure number, nominal size, pressure rating, manufacturer, and heat or lot details rather than relying on color alone. The field guide to reading hammer union markings explains what information to record before requesting a replacement.
Do not select a hammer union by appearance or nominal size alone. FIG 1502 and FIG 602 are intended for different pressure and service requirements. Use the dedicated FIG 602 vs FIG 1502 comparison to review the key selection factors, then return to this product page when FIG 1502 is the specified figure.
FIG 1502 is used for cementing, fracturing, acidizing, testing, and choke & kill line applications.
The FIG 1502 hammer union is rated at 15,000 PSI NSCWP, with a test pressure of 22,500 PSI.
The listed nominal pipe sizes are 1½ in, 2 in, and 3 in. Refer to the dimension table for the corresponding inch and millimetre values.
FIG 1502 is identified by a blue nut and red parts. Color should only be used as a quick identification cue; always verify the figure number, nominal size, pressure rating, and product markings.
The FIG 1502 union uses a replaceable resilient nitrile-butadiene rubber (NBR) seal ring.
Send AlienFrac the required nominal size, connection details, service conditions, quantity, and documentation requirements. Contact AlienFrac for a FIG 1502 hammer union quotation and technical matching review.
